One of the most important pieces of gear in your home recording studio is the audio interface. This post contains all the complete information when buying and selecting an audio interface for your studio. A lot of mistakes are being made by beginners when buying an audio interface. It is important to read this post carefully before shopping and buying this piece of gear. Audio interface is a requirement in building your studio, it is one that will convert the analog signals (those coming from your guitars, vocals, drums, etc.) to digital signals which will be saved to your computer hard drive and processed by your DAW software. It is also the one that will convert the digital signals from your computer back to analog form so that it can be played in your near field monitors and you can listen to your works. There are 3 types of audio interface:
a.) Internal/PCI based audio interface – which is popularity known as PCI soundcard.
b.) USB audio interface- audio interface that communicates to your computer via USB connections.
c.) Firewire audio interface – audio interface that communicates via Firewire connections.
Things to check when buying an audio interface
So what are the things to check when you are about to buy an audio interface? . Based on my experience below are the important factors:
1.) Connections that is supported by your computer- For example, you cannot easily install PCI soundcards to your laptop or netbook, so you will opt to select either USB or Firewire type of connections. Also if your computer does not support Firewire, you opt to select USB audio interface only. For portability and convenience, I would recommend selecting between USB and Firewire audio interface. PCI soundcards is an old type of audio interface used in digital home recording studio and would not give you the best routing flexibility and convenience today. Remember to check the supported USB version and Firewire versions of the audio interface and make sure that it is supported also by your PC or Mac.
2.) Number of inputs and outputs – it all depends on what you are trying to accomplish. For example; a singer-songwriter with only intention to produce an acoustic demo could find the two inputs and two outputs audio interface enough for the projects. However if you are looking forward to “simultaneously” record more than two inputs such as a full band recording, then you will need 4 inputs or more. A full band recording needs at least 8 inputs like one input for Vocals, two inputs for guitars, one input for bass, and four inputs on drums. For most home studio projects, 8 inputs is the best way to go as you have sufficient inputs for either small or big recording projects(e.g. with drums). Do not also forget that if you are using condenser microphone, you will need a phantom power. So ensure that your audio interface should have its own phantom power source. Outputs of audio interface are equally important as the inputs. You need more than one output, like an output for your nearfield monitor, PA speakers, headphones, etc.
3.) Availability and Quality of the Pre-amp – I recommend you should buy an audio interface with a high quality pre-amp on it. This makes hardware mixers and other outboard pre-amps/DI boxes unnecessary. You cut cost and prevent hardware clutter in your studio. “Pre-amp” is important to boost the weak analog signal coming in to your audio interface from different instruments such as guitars, vocals, drums, etc. without adding noise, coloration and distortion. A high quality pre-amp can provide better recording quality (very low noise, strong signal to noise ratio and accurate/crystal clear reproduction). So if you are using an audio interface with pre-amped inputs, you simply plug your guitar and vocal microphones directly into it and adjust the gain control for sufficient level. NOT every audio interface has a pre-amp on all of its inputs, so you need to check. For example, an audio interface can only have 2 pre-amp inputs out of the 8 inputs. There are also audio interface with pre-amps for all of its inputs. The number of preamps depends on your needs, the higher the number of preamps on the audio interfaces the better.
4.) Supported bit depth and sample rate – this is one of the most important specifications. You should ensure that it SHOULD support 24-bit recording! Most USB and Firewire audio interface today however supports 24-bit recording except for those very low budget audio interfaces that only supports 16-bit recording. For best recording quality, you should buy a 24-bit audio interface. Sample rate is not as important as bit depth. However, make sure the audio interface should support more than 44.1 KHz sample rate. So 48 KHz is OK but if it supports different sample rates like 48 KHz, 88.1 KHz, 96 KHz- the better.
5.) Does it work well with your PC, Mac, OS and recording software or DAW? –modern high quality audio interface works with either PC or Mac. Another thing to check is its compatibility with your OS version. In their specs, they will clearly state what the supported machines (PC or Mac) are and the supported OS (Mac OSx, Linux or Windows). Modern DAW and audio interface works together in ASIO mode for very low latency recording. So avoid buying an audio interface with drivers that works only in WDM. Do some research to make sure that your DAW software is supported by the audio interface. When in doubt, you can always write to the audio interface technical support team.
6.) Budget – you should be able to buy a very high quality audio interface below $500 (excluding shipping cost).
7.) Brand reputation, reviews and ratings – some audio interface brands are known for their special high quality characteristics whether it’s the driver stability, quality of the converters, pre-amp quality, etc. Some audio interface manufacturers are also known for receiving a lot of complaints. Read the reviews posted in different forums to get an idea regarding what users can say about it. You can also watch YouTube videos for music created using that audio interface to get an idea how it sound like.
8.) Bonuses– some audio interface rarely provide an additional bonus aside from the CD containing the hardware drivers. But some audio interface provides a lot of bonuses that includes high quality plug-ins, etc. This can be very useful tools for your project.
9.)Availability of Internal/Software Mixer for Input-output Routing– this is very important if you are working with a lot of inputs and outputs. Software mixer provided by the audio interface can help you check for clipped inputs, route the signal from your DAW to specific outputs, adjust levels, panning, select specific sample rate and bit depth and many more. Not all audio interfaces contain a software mixer so you need to check.
10.) Easy ability to monitor the mix in mono – it is important to check if the mix is still sounds good in mono and not only in stereo (especially for phasing issues). If the audio interface supports this feature for outputting the mono mix through your nearfield monitors; it would be an added advantage.
11.) Read and understand the manual before deciding to purchase – this is the last but very important step when buying audio interface. It is because sometimes features listed on Amazon, EBay, etc. are not enough to describe its actual usage. The full capability of the audio interface will be revealed through the user manual. Make sure you read the manual in advance and check if all those features you need are well documented and there are clear/specific instructions on how to do it.
Below are my favorite and recommended audio interface that suits well with the above requirements:
Focusrite Saffire Pro40
– with 8 high quality preamp inputs and a Firewire interface that supports 24-bit/96KHz recording. Compatible with Mac and PC.
Focusrite Saffire USB 6
Content last updated on August 8, 2012